Dead outlets & switches
We trace the fault from the device back to the source — tripped GFCI upstream, loose connection, failed device, or a broken circuit — and restore power safely.
Palm Beach County · Licensed Electrical Contractor
Electrical repair across Palm Beach County
Outlets that stopped working, breakers that keep tripping, flickering lights, dead circuits, and code corrections — diagnosed and fixed by a local, licensed electrician with up-front pricing and permits handled.
24/7 emergency responseNEC code & permit readyUp-front pricing, no surprises
Find the fault. Fix it right.
Electrical repair, done safely for Florida
An electrical problem is rarely as simple as the symptom. A tripped breaker points to an overloaded circuit or a wiring fault upstream. A dead outlet might be downstream of another outlet whose GFCI tripped silently. Flickering lights can trace back to a loose neutral connection at the panel. Good electrical repair starts by finding the real source — not resetting the breaker and hoping — so the fix holds and the hazard is actually gone.
We are a local, licensed electrical contractor repairing every type of residential and light-commercial electrical problem across Palm Beach County: outlets, switches, lighting circuits, GFCI and AFCI protection, breaker panels, code violations, and aluminum-wiring corrections. We carry our own permit accounts across every jurisdiction in the county, pull permits when the scope calls for one, and bring the work to current NEC code so it passes inspection and satisfies your insurer.
The fix
Problem identified. Circuit restored.
Drag the handle. A dead outlet bank, a breaker that won't hold, a burned device — becomes a clean, code-correct circuit you stop thinking about. That is the job a real electrical repair does, start to finish.
What we fix
The electrical problems we repair most
From a single dead outlet to repeated breaker trips and code violations, these are the calls we get most often across Palm Beach County.
Breakers that keep tripping
A breaker that trips on normal loads points to an overloaded circuit, a weak breaker, or a wiring fault. We find which, fix it, and load the circuit correctly.
Flickering & dimming lights
Flickering usually means a loose neutral, a failing connection at a junction, or a shared circuit that is overloaded. We trace it to the real point of failure.
Dead circuits & no power
Entire rooms or circuits with no power — traced from the panel to every device on the branch, with the fault found and the circuit brought back live.
Code corrections & violations
Missing GFCI and AFCI protection, undersized wiring, open junction boxes, improper grounds — corrected to current NEC code with permits pulled where required.
24/7 emergency electrical
Sparking panels, burning smells, arcing wiring, or circuits that will not shut off need immediate response. We dispatch around the clock for safety-critical failures.
Where electrical problems start
The four places we look first
Two homes the same age can have completely different electrical reliability — it comes down to the details inside the panel and the wiring behind the walls. These are the points we diagnose first on every repair call.
01
Breaker & panel connectionsLoose breaker lugs, overheated bus connections, and breakers that no longer hold their rated trip current — the most common source of repeat trips and panel heat.
02
Neutral & ground bus barsA loose neutral causes flickering, over-voltage on one leg, and blown devices across the house. We tighten, test, and verify the neutral bond is correct to code.
03
Branch circuit wiringUndersized wire, aluminum branch circuits, and deteriorated insulation behind the walls — found during the diagnostic and corrected or flagged for rewiring.
04
GFCI & AFCI protectionMissing ground-fault and arc-fault protection is a code violation and a fire risk. We add listed GFCI and AFCI devices to every circuit that the NEC requires it on.
Step by step
How an electrical repair works
From the first diagnostic call to the final inspection, here is the path every Palm Beach County electrical repair follows.
-
Diagnostic & fault tracing
A licensed electrician identifies the real source of the failure — not just the symptom — using load testing, outlet mapping, and panel inspection so the repair is targeted and complete.
-
Up-front written estimate
You get a clear, itemized price before any work begins — what failed, what we will do, and what it costs. If the panel or wiring is the real problem, we will say so and price the honest solution.
-
Permitting, where required
We carry permit accounts across every Palm Beach County jurisdiction. When the scope calls for a permit, we pull it — protecting your insurance coverage and ensuring the work is on record.
-
The repair — to NEC code
Every repair is made to current National Electrical Code (NEC) standards: correct wire gauge, listed devices, proper GFCI/AFCI protection, and a tight, torqued connection at every termination point.
-
Load test & verification
We test the repaired circuit under load, verify adjacent circuits were not affected, and confirm the panel is running at safe temperatures before we sign off.
-
Inspection & documentation
For permitted work we schedule and pass the county inspection. You receive documentation of the repair scope — useful for your insurer, your HOA, or a future buyer.
Outlet dead? Breaker tripping? Get a diagnosis and a real price fast.
Get a Free Estimate Every repair we handle
Electrical repairs by problem type
Whatever the symptom, there is a right way to fix it — diagnosed at the source, not masked at the surface.
Outlet & switch repair
Dead, sparking, or loose receptacles and switches replaced and wired correctly — GFCI and USB-C types where the NEC or homeowner requires them.
Breaker & panel repair
Faulty breakers replaced, panel connections tightened and torqued, and overloaded circuits redistributed — or a panel upgrade recommended when it is the honest answer.
Lighting circuit repair
Flickering, buzzing, and dimming fixtures traced to their source — loose neutrals, failing dimmers, or overloaded circuits corrected and retested.
GFCI & AFCI protection
Ground-fault and arc-fault protection added to kitchens, baths, garages, and other required locations — the code correction most inspectors flag first.
Aluminum wiring correction
CO/ALR device replacement and anti-oxidant pigtailing at every connection on aluminum branch circuits — the remediation insurers require and the NEC sanctions.
Surge & hurricane protection
Whole-home surge suppression installed at the panel — critical after a Florida storm event when utility-side surges can destroy appliances and electronics.
Pricing depends on the fault type, circuit length, and what we find at the diagnostic, so we quote on-site rather than over the phone. If the inspection shows the panel or wiring is the real problem, we will tell you when a panel upgrade or rewiring is the better spend. Use our electrical cost estimator for a ballpark before you call.
Repair, or upgrade?
An honest read on whether a repair is the right call
A targeted repair solves a real, isolated failure and costs far less than replacing equipment you do not need to replace yet — but chasing the same fault repeatedly on aging wiring or a failing panel is the most expensive way to avoid the real fix.
SPOT REPAIR An isolated dead outlet, a single tripped breaker, or a loose connection is a clear repair — fast, targeted, and a fraction of a panel replacement.
CODE CORRECTION Missing GFCI/AFCI protection, open junction boxes, and aluminum wiring issues must be corrected for safety and insurer compliance — we handle it.
PANEL UPGRADE Repeated trips on normal loads, a panel running hot, or a 30–40-year-old main breaker means the panel is failing — we will say so and price a service upgrade.
EMERGENCY Sparking panels, burning smells, or arcing wiring are 24/7 emergencies — call us immediately and we will dispatch to make the system safe.
The payoff
A home that runs like it should.
The right electrical repair is the one you forget you paid for — no flickering lights, no tripping breakers, no worry before the next storm. Just a safe, reliable system behind every switch in the house.
Good to know
Electrical repair FAQ
How much does electrical repair cost in Palm Beach County?
Cost depends on what is wrong and how hard it is to find — a single dead outlet or a loose connection at a junction box is often a straightforward visit, while chasing an intermittent breaker trip, correcting code violations, or tracing a fault across multiple circuits takes more time. We give you a clear, up-front price after diagnosing the problem so you are never surprised by the invoice. If the inspection turns up a failing panel or aged wiring that puts repairs on a treadmill, we will tell you plainly when a panel upgrade or rewiring is the better investment.
How do I know if I need electrical repair or a full panel upgrade?
A repair handles an isolated failure — a tripped breaker that holds after reset, a dead outlet, a single circuit that will not respond. Once breakers trip repeatedly on normal loads, the panel runs hot, you have more circuits than slots, or the equipment is more than 30–40 years old, the problem is the panel itself, not just a circuit. We give you a straight assessment at the diagnostic visit — including when a panel upgrade is the smarter spend and what it would cost — before any work begins.
How fast can you respond to an electrical emergency?
Electrical problems that put safety at risk — a panel that sparks, burning smells, a circuit that will not shut off — need fast action. We prioritize 24/7 emergency calls across Palm Beach County and work to get a licensed electrician on-site quickly to make the system safe. If you smell burning, see arcing, or have any doubt about safety, do not wait — reach us now or call (561) 919-9037.
Does electrical repair require a permit in Palm Beach County?
Minor repairs — replacing a receptacle, resetting a breaker, fixing a loose connection — generally do not require a permit. But any work that adds a new circuit, moves wiring, replaces a breaker panel, or corrects a code violation typically does, and unpermitted electrical work can void homeowner’s insurance and create problems at resale. We know each jurisdiction’s threshold across Palm Beach County, pull permits when the scope calls for one, and ensure the work passes inspection. You get documentation that the repair is legal and up to NEC code.
Can you repair aluminum wiring in older Palm Beach County homes?
Yes — aluminum branch-circuit wiring (common in homes built in the 1960s and 1970s) is a known fire hazard at device connections and must be corrected with listed CO/ALR devices or a pigtailing method using antioxidant compound and approved connectors. We identify aluminum wiring during the diagnostic visit, correct the connections at every outlet and switch on the circuit, and document the repair for your insurer. Many carriers require this remediation for coverage — we can provide the scope they need.
Get a free estimate
Tell us about your project — we'll take it from here.
A local team member follows up to answer your questions and walk you through your options, pricing, and any financing. No pressure, no call center.